Shenzhen YKS Technology Co., Ltd.
Main products:RC Hobby,RC Spare Parts,Electronic
Products
Contact Us
  • Contact Person : Ms. Lee Vicky
  • Company Name : Shenzhen YKS Technology Co., Ltd.
  • Tel : 86-755-84716935
  • Fax : 86-755-22639889
  • Address : ,,3F, Builing A2, Area B, Hekan Industrial Zone, No.41, Wuhe Road South, Bantian, Longgang District
  • Country/Region : China
  • Zip : 518000

RC GYRO KDS Flymentor 3D Auto Stabilizer Combo

RC GYRO KDS Flymentor 3D Auto Stabilizer Combo
Product Detailed
kds 450 main rotor balde carbon fiber balde C1

RC GYRO KDS Flymentor 3D Auto Stabilizer Combo

RC GYRO KDS Flymentor 3D Auto Stabilizer Combo C1 KDS flymentor 3D Combo best for 450 rc helicopter

 

RC GYRO KDS Flymentor 3D Auto Stabilizer Combo C1 

What does the flymentor 3D do? It can let you AUTO pilot the helicopter and keep it hover in FIXED position. This Flymentor 3D is consist of three modules, Flymentor Mixer, CCD Camera and 3 Axis Gyro. Flymentor Mixer This mixer is the the processer of the auto pilot system, it receives signal from the CCD Camera and the 3 Axis Gyro, then it commands all servos(Cyclic and Rudder Servos). It can be placed anywhere, just away from vibration and heat. CCD Camera Used for "Positioning Mode". The CCD Camera should be mounted underneath the main shaft or on the side frame of the helicopter, with the lens pointing at the ground and free from vibration, it works best in the attitude of 1m to 3m. The CCD Camera's job is to take image of the ground, then to provide a signal to the Flymentor Mixer, and gives the correction to the cyclic servos. To have best result, make sure that there are enough light intensity and something easy to locate on the ground surface, like grass, because the Camera can't see very well in dim condition and it can't recognize flat snow or flat sand, it requires "Something" to see, it will not work in dim condition or low contrast color surface. 3 Axis Gyro 3-Axis Gyro means it can sense X, Y and Z axis moments, that means body leaning forward / backward, body rolling left / right, tail drifting CW / CWW, it will constantly monitoring any off-balance in all directions, then it will give signals to all CCPM servos and Rudder servo to balance the helicopter, it works constantly and unless you have the helicopter drifts too much, you will not even notice the system exists. This gyro also contain some Temperature sensor and some other sensors too. Also, needs to isolate it from vibrate and heat. The following diagram will simply tell you more on how it works. Here are some highlight features of the KDS Flymentor 3DControl all movement. including attitude stabilization, speed control, position locking.CCD sensor to capture picture of ground, comparing pictures to avoid drifting.Switch working mode (horizontal mode and position mode) through AUX channel.Integrating head locking gyro and swash plate mixer.Control sensitivity 3S 120, 3S 140, 4S 90, 4S 90+45.Keep balance in inverted flight.Configured by computer through USB.If you are using FM/PPM remote control device, when helicopter is out of control, the Flymentor 3D will set aileron, elevator, rudder to neutral, and keep pitch in the final signal position, and switch to positioning mode automatically, the sensitivity is 70%.

 Spec.

Voltage: 4.8 - 6.0VCurrent: 55mA (under 5V)Temperature Range: 0°C - 40°CWeight: 37gThe software only work on Windows XP. It DO NOT work on Vista or Windows 7 yet1 x KDS Flymentor 3D Set1 x Installation Guide & Software CD

RC GYRO KDS Flymentor 3D Auto Stabilizer Combo



Copyright Notice @ 2008-2012 ECVERY Limited and/or its subsidiaries and licensors. All rights reserved.